The MOST

Hello Fltcrew21...the gelcoat part numbers, codes and contact info is now in the "Product Support" section under General Care Maintenance manuals.

Hello Dan, Those rocker switches were distributed by Wes-Garde Components (800-554-8866) or www.wesgarde.com. The rocker switches are probably the V series, Contura III which the panel vendor used most often on the 282 Cruiser. Those were manufactured by Carling Technologies (www.carlingtech.com) or 860-793-9281 which were sold through Wes- Garde Components.

Hello Gavin, At the bottom edge of the coaming panels you will see screws- remove those and then gently pull straight upward on the entire piece. It is held in place with "J" hooks which allow the panel to slide on and off.

Hello Steve, The forward ladder is designed for boarding from the beach or sand bar. Make certain that the side supports are pulled all the way out before extending the ladder downward.

Spectrum Gelcoat Color Chart.pdf www.spectrumcolor.com or 1-800-754-5516

Too funny Rip5...the lights were part number 24077-65 white oval and the manufacturer was Liteco (a division of Ramco). Contact phone is 800-826-5483. You can probably find them at West Marine or any marine supply store...

Hello Coolhand 37, Pearl white was the color name, Spectrum part number is 18027, the manufacturer was Cook Composites and their part number was GELCOAT 954-WA-446 1997 (for MiniCraft).

Hello Captbro, That was a Lenco part #HL-2400S- LIFT.

Hello Oban, Your best source of help is most likely the engine manufacturer: www.volvopenta.com (for your nearest authorized service center) or 757-436-5100 (in VA). The Volvo technician will be able to hook up your engine to his computer and read any error codes. That is also a good way to give the engine a preventative maintenance "check up". Just in case- your gauges are manufactured by Faria and they do have a limited lifetime warranty. Contact info for warranty and trouble shooting is: www.faria-instruments.com or 1-800-473-2742 (CT).

Hello VIP, Your gauges are Faria and they do have a limited lifetime warranty. Contact info for warranty and trouble shooting is: www.faria-instruments.com or 1-800-473-2742 (CT).

Hello Jurij, Thank you for the HIN. Your exterior gelcoat Spectrum part number is: 18001- PEARL WHITE (ASHLAND) WG-LF-1977.

Hello Greg, The ski locker should be draining into the bilge. Have you had the boat since 1997? Has work been done on it lately? Has the boat been sitting-if so, there could be a mud-dobber's nest or similar insect's nest in the drain's path. When you say, "I've tried running a fish tape up the drain pipe that runs into the bilge without success". Do you mean the tape gets stopped by something?

Hello Capt bro, Manufacturer/distributor is Forespar (949-858-8820) and their part number is: STRAINER SCOOP-P/U906059. Web is www.forespar.com.

Hello Andy208, You can purchase new MONTEREY logos from any authorized Monterey dealer. You can see the logos at our home page under the Sport Boat Collection. Graphics removal is normally done with a specific type of heat gun (we recommend you use a professional graphics installer) and there is usually very little adhesive residue left when properly removed. If there is any, denatured alcohol will clean it up.

Hello Bob, Unfortunately, the original vinyl material is no longer available from the manufacturer. Also, the exact color information is not available in our system, we must purge parts information about every ten years or so in order to obtain space. If your upholsterer cannot match the color visually, then perhaps go with a two color piece or a complementing color to your canvas(?).

Hello m_cogs, The waste pump out for the head was an option on the 2002 248LS and it is designed to be pumped out at a waste "dump" facility. Most marinas offer this service as well as RV/Motorhome/camping parks. Grey water such as the sink and shower goes directly overboard unless you have a "greywater system" installed. There is an automatic float switch on the bilge pump. To manually operate it, turn on the accessory switch on the dash and then the bilge switch on the dash.

Hello ms-200LS, After much research- That was a Taylor Made part and I am not certain if they still make it in the plastic. I found a stainless steel one that looks really close and it is part #13008 ROUND HEAD SIDE MOUNT. you might have to change out both sides to get a match. Your best bet would be to contact their Customer Service, Technical help at 518-773-0636. I am certain if you send them the photo it will solve your problem.

Hello awood147, The factory installed air conditioner was a Marine Air product and the part number was: #VCD5K115V 115V AIR CONDITIONER (DOMESTIC use part #). For tech support: Dometic Corporation, Environmental Division 2000 N. Andrews Ave. Ext. Pompano Beach, FL 33069 Phone: 954-973-2477 on line: www.dometic.com It might be something as simple as the pump needing to be primed but the clicking noise sounds like there could be something wrong.

Hello Fratalia17, That was not a factory option on the 245 Cruiser. It could probably be done by a good upholstery shop...

Hello gpw16, You can purchase the camper option direct from Taylor Made Group: Taylor Made Systems Taylor Made Group, LLC 93 South Boulevard Gloversville, NY 12078 PH: 518-773-0636 Please e-mail us for additional information on any of our products and services at tms@taylormadesystems.com. REPLACEMENT OR SERVICE PARTS and ** ALL DIRECT-TO-CONSUMER INQUIRIES ** CUSTOMER SERVICE: 518-773-0636 If you are a boat owner, marina, service yard, or other non-O.E.M. customer (i.e. not the manufacturer of the original boat), please call the number above for the fastest service. Email: tms@taylormadesystems.com Part numbers for the 2003 302 Cruiser camper canvas are: CANC-CMP-2922-NVY 1EA 302CR CAMPER TOP W/BOOT(#29226046201) CANC-CAFT-2922-NVY 1EA 302CR CAMPER AFT CURTAIN(#29226046231) CANC-CSID-2922-NVY 1PR 302CR CAMPER SIDE CURTAIN(#29226046221)

hello Cibolariverman, You must be talking about a Merc. The tapered side (angled) goes against the prop, tapered side to tapered side above and below.

Hello Rip5, The factory installed windlass was a Simpson Lawrence Sprint 600 and the breaker (the windlass was an option) is located on the main DC panel in the engine room. See attached photo. For technical support: www.lewmar.com or contact your local Lewmar dealer by using the locator on their site. 10 is the Main DC panel and the windlass breaker is located in the center.pdf

Hello Savarese1, The nav lite is a Perko product, part #227 BI-COLOR...www.perko.com on line. The instructions were on their site under Technical: To Re-Bulb: Remove two mounting screws and lift light off deck. While upsidedown, use a small bladed screwdriver (in either of the two slots) to pry out the bulb holder. Replace bulb and snap back into place. Re-mount light. I hope this helps!

Hello Mike, Contact the manufacturer direct for tech help, Corsa Performance Exhaust (Quick and Quiet) contact info: www.corsaperf.com or 800.486.0999 in Ohio. There is alot of information on their site also. You might be able to manually shut it off at the exhaust solenoids- each one is independent and there are 2 on each engine. The exhaust normally defaults to the closed position when the disconnection occurs....but if it was not factory installed I can't be sure. It would be best to seek the advice of a Corsa tech direct.

Your tachometer does have a limited lifetime warranty...contact Faria Instruments at: www.faria-instruments.com or 800-473-2742.