Rip5
-
Content Count
480 -
Joined
-
Last visited
Posts posted by Rip5
-
-
Your float in your drive lube reservoir is likely stuck. Pull the wires from it and see if the beep stops.
If so, order a new one. Common wear and tear item on Merc's
-
Local Canvas Shop
-
You will need a harness similar to this. I think it will be difficult to tow a wakeboard, but tubes will be fine.
Lot's of choices available.
-
Good chance it is a Teleflex system. We had a 2005 282CR, but never had a reason to adjust anything.
The slack can probably be taken out with a cable adjustment. No experience with it myself.
-
Get in the water, have someone move the switches up/down. Observe if they move. If they do, you are fine.
If they don't, you may need the rams re-built.
-
Lift up maybe ? Many builders have clips behind them that just lift up to remove the panels.
-
-
Thanks for the follow up. Glad you are back on the water.
-
On 6/3/2017 at 4:39 AM, tallman696@msn.com said:I have a 2007 194fs. There is a sink in the port side of the rear swim deck with a fresh water sprayer in it. The switch turns on a pump to pump water from ur fresh water tank to the sprayer. There is a fresh water fill in the built in cooler in the starboard side of the swim deck with a 12 gallon fresh water tank that sits in the left side of the engine bay.
Only if that option was ordered. If you have no sink, the switch is not connected or used.
-
Cooler, lines, or fenders can go there.
-
Get a :
Michigan Wheel XHS Ballistic 14-3/8 x 21 RH 933521 SS propeller.(Will need a XHS 205 hub kit as well)
-
Where is "over here" ???
-
Good advice that I have seen on another board before. Curious why a Shamrock boat owner is posting on a Monterey Boats owner's site ?
Glad you felt the urge to share some of your knowledge. Whatever the motivation.
-
It manually turns on your automatic bilge pump(s)
You should check connection at the pump to see if it has power. If it does not turn on when hitting the switch,
your bilge pump(s) may not be working. Potential dangerous situation.
-
From the picture posted, it does not look like port lite trim, but rather windshield seal/gasket.
If so, try here. Since they made your windshield.
http://www.taylormadesystems.com/hardware/parts/walkThruParts/index.html
If it is port light parts, this is your source.
-
Letter "D" in above picture........
-
Look at page M-3 of the owner's manual. It shows all the switches on a 270CR. The one labeled "Eng. Rm. Lights" is the correct one.
The switch is between the cockpit light and Bilge switch.
-
Easiest answer I have ever had to give on this forum. Best place in the states for carpet.
-
Note: this thread is 2 years old, hard to say if the OP even still owns a 276. Good Luck with your's.
-
I have a 2000 322 crusier. Someone cracked the hatch lens over the front birth. Is there anyway to replace just the lens? And where would I find one?
Chris
Checking the manufacturer's website is usually a good place to start.
https://www.pompanette.com/BigSummit/pomp.nsf/Marketing/bomar_catalog
-
Whatever fits. Danforth type held our 204FS just fine.
-
Try iBoats.com
-
On Line boat ads. Boattrader, Yachtworld etc.
-
Call a local canvas shop. Or order one from your dealer direct from Monterey. Those are your choices.
282 bilge pump locations
in Technical Discussion
Posted · Report reply
our 282 did not have a forward bilge pump. Only in the bilge. I suspect your's is the same.